ifyoreo.blogg.se - Drok battery monitor manual

#DROK BATTERY MONITOR MANUAL FULL#
#DROK BATTERY MONITOR MANUAL PLUS#

As the following picture shows: (Note: if you input voltage is higher than 80V, please add ventilation and cooling and also we suggest to add separate power supply for this meter.) Making the red wire and yellow wire in parallel and then connect it to the positive of battery. When the measured voltage is DC 5-90V, this meter can be connected with two-wire system connection.

Yellow wire is for the input lead wire of the measured voltage, ii have to be connected to the lead wire of the measured voltage.

Red wire is for power supply+.( Note: power supply range must be DC 5-90V, or this meter will be burnt.).

There are 3 wires on the back of meter, as following: If the measured voltage is DC 5-90V, you can use two-wire system connection to make it work, which is easy and simple. This meter, with 3 wires, allows to be powered by wide voltage range and has a wide voltage measuring range. )Ĭapacity measuring range 0~ 999AH Power measuring rangeīacklight on : 10MA Backlight off: 4MA Wiring instructions:

(Note: HU XXX.X LU XXX.X HAXXX.X, if the 3 parameters display as 000.0, that means the alarming function is off, factory setting is off.

#DROK BATTERY MONITOR MANUAL FULL#

(Note: We suggest to set the voltage as the voltage when full charged.)īy using the same setting method to set the value of overvoltage alarming, low voltage alarming and over current alarming. When standby, press key to switch to menu “FU XXX.X”, press key to set parameters and keep pressing to save set parameters. Setting method for automatically filling voltage when full charged(The same as setting method for rated capacity of battery) If you want to set battery’s rated capacity as 20AH, just set the menu parameter as AH 020.0, then keep pressing the key, finally release the key, you can make it stored successfully.

parameters will be stored, at this time, menu will flash twice that means you have set successfully.Įg.

Keeping pressing key, then release the key, the set.

In this way, you will finish setting 4 digits.

#DROK BATTERY MONITOR MANUAL PLUS#

At this moment, pressing key, the digit will plus 1,too. finishing setting this digit, the next digit will automatically flash when no any action in 5s.The first digit on menu parameter will keep flashing, at this time, pressing key, the digit will plus 1.When standby, press key to switch to menu “AH XXX.X”.Setting method for rated capacity of battery: (5) “HA XXX.X” Setting Menu for over-current alarming (4) “LU XXX.X” Setting Menu for low-voltage alarming (3) “HU XXX.X” Setting Menu for over-voltage alarming (2) “FU XXX.X” Setting Menu for fulfilling voltage when full charged (1) “AH XXX.X” Setting Menu for rated capacity of battery When standby display, press key to switch menu in order. When standby display, to keep pressing key and release the key will clear positive and negative bidirectional accumulated electric energy. When standby display, to keep pressing key will clear current to zero if no load is connected.(Note: if you don’t clear current when no load connected, it will be inaccurate.) Backlight mode will be save when power-down. When standby display, press key to turn on or turn off the backlight. Capacity of battery and accumulated electric energy will be saved automatically when power down. It has the function of clearing current and accumulated electric energy data and the function of storing data when power-down.It will automatically fill the capacity of battery when it is full voltage.It will also alarm and flash to draw your attention when the remaining capacity of battery is low and the battery icon will keep flashing that means you need to charge for your device. The preset voltage and current could be adjusted as you need.

Alarm flashing function: it will alarm and flash to draw your attention when the real voltage is higher or lower than preset alarm voltage and real current is higher than preset current.

This meter can be used to measure percentage and AH of remaining capacity, DC positive and negative bidirectional current, DC voltage, DC positive and negative power, DC positive and negative bidirectional accumulated electric energy.